Hyundai Elantra HD: Repair procedures
Inspection
Burglar Alarm Horn Relay
Check for continuity between the terminals.
| 1. |
There should be continuity between the No.8 and No.18
terminals when power and ground are connected to the No.6 and No.19
in the ICM-B.
|
| 2. |
There should be no continuity between the No.8 and
No.18 terminals when power is disconnected.
|
Burglar Alarm Relay
Check for continuity between the terminals.
| 1. |
There should be continuity between the No.3 and No.10
terminals when power and ground are connected to the No.1 and No.11
terminals in the ICM-A.
|
| 2. |
There should be no continuity between the No.3 and
No.10 terminals when power is disconnected.
|
Front Door Lock Actuator
| 1. |
Remove the front door trim.
(Refer to the Body group - Front door)
|
| 2. |
Remove the front door module.
(Refer to the Body group - Front door).
|
| 3. |
Disconnect the connectors from the actuator.
|
| 4. |
Check actuator operation by connecting power and
ground according to the table. To prevent damage to the actuator, apply
battery voltage only momentarily.
|
Rear Door Lock Actuator
| 1. |
Remove the rear door trim.
(Refer to the Body group - Rear door)
|
| 2. |
Remove the rear door module.
(Refer to the Body group - Rear door)
|
| 3. |
Disconnect the connectors from the actuator.
|
| 4. |
Check actuator operation by connecting power and
ground according to the table. To prevent damage to the actuator, apply
battery voltage only momentarily.
|
Trunk Lid Lock Actuator Inspection
| 1. |
Remove the trunk trim. (Refer to the Body group -
tailgate)
|
| 2. |
Disconnect the 3P connector from the actuator.
|
| 3. |
Check actuator operation by connecting power and
ground according to the table. To prevent damage to the actuator, apply
battery voltage only momentarily.
|
Front Door Lock Switch
| 1. |
Remove the front door trim.
(Refer to the Body group - Front door)
|
| 2. |
Remove the front door module.
(Refer to the Body group - Front door).
|
| 3. |
Disconnect the connectors from the actuator.
|
| 4. |
Check for continuity between the terminals in each
switch position when inserting the key into the door according to the
table.
|
Rear Door Lock Switch
| 1. |
Remove the rear door trim.
(Refer to the Body group - Rear door)
|
| 2. |
Remove the rear door module.
(Refer to the Body group - Rear door)
|
| 3. |
Disconnect the connectors from the actuator.
|
| 4. |
Check for continuity between the terminals in each
switch position according to the table.
|
Trunk Lid Switch
| 1. |
Remove the trunk trim. (Refer to the Body group -
Tailgate)
|
| 2. |
Disconnect the 3P connector from the actuator.
|
| 3. |
Check for continuity between the terminals in each
switch position according to the table.
|
Door Switch
Remove the door switch and check for continuity between the
terminals.
Hood Switch
| 1. |
Disconnect the connector from the hood switch (A).
|
| 2. |
Check for continuity between the terminals and ground
according to the table.
|
Key Warning Switch
| 1. |
Remove the crash pad lower panel. (Refer to Body
group-Crash pad)
|
| 2. |
Disconnect the 6P connector from the key warning
switch.
|
| 3. |
Check for continuity between the terminals in each
position according to the table.
|
Burglar Horn
| 1. |
Remove the burglar horn after removing 1 bolt and
disconnect the 2P connector from the burglar horn.
|
| 2. |
Test the burglar horn by connecting battery power
to the terminal 1 and ground the terminal 2.
|
| 3. |
The burglar horn should make a sound. If the burglar
horn fails to make a sound replace it.
|
